CNC Controller Kits(G203V G201X)

  This package contains the essential component to put together a 2 axis Stepper Drive Controller based around GeckoDrive G201X Stepper drives. The Kit uses  640oz.in stepper motors for the X and Y axes,   The Kit contains the...

Super flexible four core cable perfect for larger stepper motors Cable Outer Diameter 7.5mmRed, Black, Blue, Yellow ConductorsConductors: 40x0.16mm2 OFCSold per Meter.

The MB-02-V6 is a simple but robust breakout board that provides a convenient and safe way to interface your CNC components to your PC via the parallel port. Additionally the Breakout board may be used to connect your CNC components to a Smooth...

The new DigiSpeed-DC-03 V3 generates an isolated interface for control of CNC equipment that requires an analog control voltage input; The board can generate the isolated analog voltage from the following sources. 0-5V Analog voltage signal as...

  Dual Channel 5V Relay Module This is a dual channel 5V coil relay module.This board is ideal for use with the MB-02V6 Breadout board Active Hi or Active Low  selection jumper Contact Form: SPDT Contact Rating 10A Coil Voltage 5V...

  Model No. SE-600-48 MeanWell 48V DC 12.5A 350W  Power Supply AC input active surge current limitingAC input range selectable by switchProtections: Short circuit / Overload / Over voltageForced air cooling by built-in DC fanPWM control and...

Model No. NES-15-05   Genuine Meanwell 5V DC 3A 15W  Power Supply AC input range 110V - 240V, 50/60HzOutput 5Vdc 3A Protections: Short circuit / Overload / Over voltageAuto Recovery after protectionLED Power Indicator Cooling by Free air...

This is a dual shaft bipolar  570oz-in Nema 24 (60mm) Stepper Motor. Model Number: 24H2100-50-4B Specifications Size: Nema 24 Phase: 2 Phase Step Angle: 1.8 Degrees Voltage: 50V Max Current: 5A Resistance: 0.6 ohm/phase Inductance: 2.1...

This is a single shaft bipolar  640oz-in Nema 34 Stepper Motor. Model Number: 4H280-60-4A Specifications Size: Nema 34 Phase: 2 Phase Step Angle: 1.8 Degrees Voltage: 80V Max Phase Voltage1.8V Current: 6A Resistance: 0.3 ohm/phase...

This is a single shaft bipolar  1200 oz-in Nema 34 Stepper Motor. Model Number: 4H2120-60-4A Specifications Size: Nema 34 Phase: 2 Phase Step Angle: 1.8 Degrees Voltage: 80V Max Phase Voltage 3.3V Current: 6A Resistance: 0.55 ohm/phase...

Quality Omron Watertight Snap action micro switch with short lever with roller suitable for limit and/or home switches. High-quality watertight , high-precision miniature Snap Action switch. Switch Body meets IP67 requirements Use of epoxy resin...

 A neat solution to cover the stepper motor back side providing connector interface, motor wiring protection and rear shaft (if applicable) protection. An aesthetic solution to a common problem Connector interface for easy maintenance and...

Latching Emergency Stop Switch Essential for installations of CNC equipment. Latching actuator with rotating release and normally closed contacts. When the actuator is pushed in, the contacts open and the switch is latched, ensuring the equipment...

Single phase solid state relay.     Features:     Built-in varistor effectively absorb external surges Zero crossing turn on circuit for lower EMI generation Includes internal snubber for switching inductive loads like motors...

IEC Chassis male power plug with an integral switch and fuse. Perfect for your CNC controller box. Cut-out dimensions  47mmx27.5mmDouble Pole Single Throw switch (DPST)Integral Fuse holder (Fuse not included)

Labour Cost